What did you do to your Raptor today? (Gen2)

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

Nick@Apollo-Optics

Supporting Vendor
Supporting Vendor
Joined
Apr 3, 2011
Posts
7,470
Reaction score
3,123
Location
Houston, TX
Super excited to get her back from the shop. Had these goodies added to balance out the Eibach springs up front. Thanks Nick @ Apollo and Aleks @ Alekshop

b33d546b4163a23647575f7d021f5428.jpg

8de34a906066b79b6b65c664477b2be1.jpg


Sent from my iPhone using Tapatalk Pro

Looking good, man! Hope you enjoy the new setup!

Stainless Works Dump exhaust installed!! Bumper looks much better without the exhaust sticking out..sounds great too can’t wait to hear it when it gets some carbon build up. Thanks again Nick!

a1c2cdb58496657100ba280a6e5812dd.jpgbae0a9e2eb0fe91cc9ce30d7401681a5.jpg30e2ff5e396c070f6d9411171d0d8eee.jpg


Sent from my iPhone using Tapatalk Pro

That SW exhaust really cleans up the rear end. Looks sharp!
 

Kirby Lastinger

Full Access Member
Joined
Nov 10, 2018
Posts
287
Reaction score
214
Location
Lakeland, FL
Got my CVF intercooler installed. Definitely a well built piece. Much larger and heavier than the stock unit is.

A few tips as there are no instructions. There are a couple of good YouTube videos on the install. I will say CFV tech did respond quickly back to a question I emailed them about the shroud.
1. A floor jack is helpful with the install.
2. The shutter shroud does have to be removed.
3. Be sure and get the fans reinstalled prior to raising the IC into position, as the seats for it are above and in front of the IC mounts.

Took me about 3 hours. Would take me about 2 now that I have done it once.

. 81328f84ac696a6339907e62cae01901.jpgd57c03f12f177fbf574c22722a479686.jpg6fc5b49ad328da496cfbba0af20ff2c1.jpg28ec93758579336a19e92e6182a86035.jpg1440f472026d70114524a94b2480063f.jpg


Sent from my iPhone using Tapatalk Pro
 

MJK

Full Access Member
Joined
Apr 3, 2019
Posts
349
Reaction score
431
Location
Texas
Was going to remove my hooks as I didn’t like them sticking out so far with this bumper but after looking just moved them back a little instead. Turned out the back hook bolt holes and the front skid plate bolt holes in the frame line up perfectly for the hooks

142a208a8561dcd080fb67f65a85e4a5.jpg
4979f6d03db549b62a4d496dbc14ae6a.jpgf3d0ad37454f5e2f89e6bad38acdef70.jpg


Sent from my iPhone using Tapatalk Pro
Stock suspension and tires?
 

Turbogoat324

Full Access Member
Joined
Sep 17, 2018
Posts
731
Reaction score
431
Location
SoCal
Stainless Works Dump exhaust installed!! Bumper looks much better without the exhaust sticking out..sounds great too can’t wait to hear it when it gets some carbon build up. Thanks again Nick!

a1c2cdb58496657100ba280a6e5812dd.jpgbae0a9e2eb0fe91cc9ce30d7401681a5.jpg30e2ff5e396c070f6d9411171d0d8eee.jpg


Sent from my iPhone using Tapatalk Pro

looks awesome! Would you be able to take a few more pics in daytime!
 

Mbdurham

Full Access Member
Joined
May 10, 2019
Posts
499
Reaction score
517
Location
Georgia
Got more pics of you truck


Some not so good ones as it needs to be cleaned badly

4d6a0907782d264fe38093575bfbc204.jpg

138b9a0bf6306b03bd202112427dcd00.jpg



Sent from my iPhone using Tapatalk Pro7cd52a5e547700e95fb937e5c5005772.jpg
 
Last edited:
Top