Multiple Faults No Throttle on Startup- Truck Fine after Restart

[Nibbl3s]

Resurrected an old thread, but I pulled my faults with forscan and didn't want to clutter that thread. I wanted to see if any one has any experienced this/ and or if it is worth a trip to the dealer. I have a 2019 with 6K miles. Forscan and pedal commander are my only mods. No issues at all up to this point. I was running around today and I parked for ten minutes. I used the app to start my truck, and when I got in the dash was like a Christmas tree with the following faults:

• Wrench Icon
• Collision Warning Not Available
• Traction Control On
• Hill Start Assist Not Available
  
• Collision Sensor Fault
• Hill Start Assist Fault
• Supplemental Restraint Fault
• Powertrain System Fault
• Hill Descent Fault
• Emergency break functionality limited

I had no throttle response. Multiple quick succession restarts, and the faults remained. I turned it off, and let it sit for 5 minutes. I restarted it and everything was fine, and has been since. I pulled my codes, which are below. Do you think this is a transient gremlin? or should I get this checked out? seems to me like there was a crazy communication error and a restart cleared it?


Code: U0401 - Invalid Data Received from ECM/PCM A

Status:

- Previously Set DTC - Not Present at Time of Request

- Malfunction Indicator Lamp is Off for this DTC

- Test not complete

Module: Transmission Control Module

------------------------------------------------------------------------------------------------

Code: P060D - Internal Control Module Accelerator Pedal Position Performance

Status:

- Previously Set DTC - Not Present at Time of Request

- Malfunction Indicator Lamp is Off for this DTC

- Test not complete

Module: Powertrain Control Module

----------------------------------------------------------------------------------------------------------

Code: P2138 - Throttle/Pedal Position Sensor/Switch D/E Voltage Correlation

Status:

- Previously Set DTC - Not Present at Time of Request

- Malfunction Indicator Lamp is Off for this DTC

- Test not complete

Module: Powertrain Control Module

---------------------------------------------------------------------------------------------------------------

Code: U0401 - Invalid Data Received from ECM/PCM A

Status:

- Confirmed - malfunction is confirmed

Module: On Board Diagnostic II

--------------------------------------------------------------------------------------------------------------------

Code: U0401 - Invalid Data Received from ECM/PCM A

Status:

- Previously Set DTC - Not Present at Time of Request

- Malfunction Indicator Lamp is Off for this DTC

Module: Occupant Classification System Module

-----------------------------------------------------------------------------------------------------------------

Code: U0146 - Lost Communication With Serial Data Gateway A

Status:

- Previously Set DTC - Not Present at Time of Request

- Malfunction Indicator Lamp is Off for this DTC

- Test not complete

Module: Antilock braking system

-----------------------------------------------------------------------------------------------------

Code: U0401 - Invalid Data Received from ECM/PCM A

Status:

- Previously Set DTC - Not Present at Time of Request

- Malfunction Indicator Lamp is On for this DTC

- Test not complete

Module: Antilock braking system

---------------------------------------------------------------------------------------------------------------

de: B00A0 - Occupant Classification System

Additional Fault Symptom:

- Event Information

Status:

- Previously Set DTC - Not Present at Time of Request

- Malfunction Indicator Lamp is Off for this DTC

Module: Restraint Control Module

--------------------------------------------------------------------------------------------------

Code: U0401 - Invalid Data Received from ECM/PCM A

Status:

- Previously Set DTC - Not Present at Time of Request

- Malfunction Indicator Lamp is Off for this DTC

Module: Power Steering Control Module



Freeze Frame :

-STEER_FEEL: Comfort - Steering Personalization Status

-STRWHL_POS_CAL: No - Steering Wheel Position Sensor Calibration

-SW_RAW: -0.30 ° - Steering Wheel Angle - Raw

-SW_ANGLE: 17.30 ° - Steering Wheel Angle

-SSHFT_TQ_S2: 1.2 Nm - Steering Shaft Torque Sensor #2

-SW_ALIGN_OFSET: -16.80 ° - Steering Wheel Angle Alignment Offset

-TOTDIST: 10557.0 km - Total Distance

-GLOBTIM: 15656648 sec - Global real time

-MOD_SUP_V: 13.40 Volt - Module Supply Voltage

-PSCM_INT_TEMP: 46 °C - PSCM Internal Temperature

-EPAS_MOTOR_CUR: 7.90 Amper - EPAS Motor Current

-VSS: 0.0 km/h - Vehicle Speed

-----------------------------------------------------------------------------------------------------------

Code: U0401 - Invalid Data Received from ECM/PCM A



Status:

- Previously Set DTC - Not Present at Time of Request

- Malfunction Indicator Lamp is Off for this DTC



Module: Vehicle Dynamics Module



Freeze Frame :

-GLOBTIM: 61159 sec - Global real time

-TOTDIST: 10557.0 km - Total Distance

-VSS: 0.0 km/h - Vehicle Speed

----------------------------------------------------------------------------------------------------------

Code: U0401 - Invalid Data Received from ECM/PCM A

Additional Fault Symptom:

- Signal Invalid

Status:

- Previously Set DTC - Not Present at Time of Request

- Malfunction Indicator Lamp is Off for this DTC

Module: Image Processing Module A

----------------------------------------------------------------------------------------------------------

Code: U0418 - Invalid Data Received from Brake System Control Module A

Additional Fault Symptom:

- Signal Invalid

Status:

- Previously Set DTC - Not Present at Time of Request

- Malfunction Indicator Lamp is Off for this DTC

Module: Image Processing Module A

 

[David Godbee]

I have an 18 with 11000 miles and mine did the same thing for first time today. Had to go to work so it was left in garage till I get home. Hope mine clears also. I also have Peddle com. with no issues thus far. no other mods except lights. Scratching my head also.

 

[Nibbl3s]

I have an 18 with 11000 miles and mine did the same thing for first time today. Had to go to work so it was left in garage till I get home. Hope mine clears also. I also have Peddle com. with no issues thus far. no other mods except lights. Scratching my head also.

Let me know how it turns out. I let the computer reset for five minutes and it was fine after

 

[smurfslayer]

Code: P060D - Internal Control Module Accelerator Pedal Position Performance

Status:

- Previously Set DTC - Not Present at Time of Request

- Malfunction Indicator Lamp is Off for this DTC

- Test not complete

Module: Powertrain Control Module

----------------------------------------------------------------------------------------------------------

Code: P2138 - Throttle/Pedal Position Sensor/Switch D/E Voltage Correlation

Status:

- Previously Set DTC - Not Present at Time of Request

- Malfunction Indicator Lamp is Off for this DTC

- Test not complete

Module: Powertrain Control Module

---------------------------------------------------------------------------------------------------------------

Those alerts for previously set DTC, not current seem to implicate the pedal commander. Did you have an issue installing it, or are you running around in “sport +4” on the P/C ? (Jayzuss.. I can’t imagine the throttle response on that)

I haven’t seen the Christmas tree on the dash, but definitely sounds like a module not liking something and crying about it.

 

[Nibbl3s]

Those alerts for previously set DTC, not current seem to implicate the pedal commander. Did you have an issue installing it, or are you running around in “sport +4” on the P/C ? (Jayzuss.. I can’t imagine the throttle response on that)

I haven’t seen the Christmas tree on the dash, but definitely sounds like a module not liking something and crying about it.

I run it city -2. No issues installing it or in use until this point (or after)

 

[GCATX]

My Pedal Commander made my truck do similar. It was very occasional, until it wasn't. Happened several times the last day I used it, limped the truck home, removed it and threw it in the trash. Never any problems like this with out it installed.

I got the Burger Pedal Tuner, $100 cheaper but no bluetooth (never used the bluetooth). Been running it for a few weeks, no issues yet.

FYI, I did buy the Pedal Commander used, so who knows. Maybe the wires were stretched or..? It worked great when it worked.

 

[smurfslayer]

@Nibbl3s, is your PC a bluetooth model?

I’ve never had this come up and have run a P/C since sometime in ’17.

 

[Nibbl3s]

@Nibbl3s, is your PC a bluetooth model?

I’ve never had this come up and have run a P/C since sometime in ’17.

Nope it’s the original model. I ran it on my 17 for two years with no issues. I vaguely remember something similar happening once in startup, but I am not sure

I don’t want to remove yet, in hopes this was a random gremlin. I just hope this doesn’t occur when the car is moving

 

[smurfslayer]

Maybe re-do the p/c install? if you don’t have a good connection, not seated correctly, strange things can happen.

 

[TurboTJ]

Sounds exactly like mine. There are two theories as far as I can tell.
1) water in the wiring harness connector in the driver side wheel well - did you go through water recently? Mine did it after a car wash
2) the gateway module needs to be replaced. This is what the dealer ended up doing on mine.

See my thread here: https://www.fordraptorforum.com/threads/help-brand-new-raptor-won’t-start.69419/page-3#post-1389129

I will update it tonight with the outcome. I am 100% stock