Found that Damn Rattle

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

darkneo

Full Access Member
Joined
Jan 21, 2017
Posts
163
Reaction score
90
Location
Los Angeles
I have this rattle coming from the driver side window switch panel. Anyone know of a fix? I popped it off but didn't see anything loose in there.
 

TXCobra

Full Access Member
Joined
Jan 15, 2011
Posts
310
Reaction score
195
Right?? That’s the primary reason I’ve always owned ford over chevy. My Vette rattles like crazy. At the moment the only rattle on my raptor is the sunroof but I’ve had the roof on all 4 of my raptors and never had any of them rattle but this one. My ‘08 Shelby doesn’t have a single rattle or squeak.
 

Droid

kglesq's Brother
Joined
Sep 25, 2010
Posts
1,486
Reaction score
757
Right?? That’s the primary reason I’ve always owned ford over chevy. My Vette rattles like crazy. At the moment the only rattle on my raptor is the sunroof but I’ve had the roof on all 4 of my raptors and never had any of them rattle but this one. My ‘08 Shelby doesn’t have a single rattle or squeak.

Try loosening the sunroof fixed rear panel just like the OP. I had to do this to mine too, also got the Kryton GPL 205 grease and between the two it's relatively silent now. For mine the rear of the fixed panel is as low as it can go, and the front is about midway. Even side-to-side. You'll want a T25 Torx + ratchet + short extension and about 10 minutes.
 

zudnic

Member
Joined
Jul 30, 2019
Posts
16
Reaction score
15
Location
MA or VT
Well done researching. It’s a known problem. I can confirm... lube the seals of the roof window and problem is gone.


Krytox GPL205 Performance Lubricant Grease

Amazon can supply...


Sent from my iPhone using Tapatalk

This thread was perfect! That sounds was driving me nuts. I've order the Krytox but while I was waiting I squirted a little silicone spray around the rubber weather stripping....no more rattle/squeak.

While I was doing that I noticed that there's a decent amount of play when I push on the panel from above. For those of you that removed and reset the (6) screws that hold it in place, is the play gone completely? I haven't done so yet, but I'm just trying to figure out if that's work fussing with.
 

Badgertits

FRF Addict
Joined
Jan 24, 2019
Posts
2,813
Reaction score
2,450
Location
Ma
Right?? That’s the primary reason I’ve always owned ford over chevy. My Vette rattles like crazy. At the moment the only rattle on my raptor is the sunroof but I’ve had the roof on all 4 of my raptors and never had any of them rattle but this one. My ‘08 Shelby doesn’t have a single rattle or squeak.

I actually think vettes rattle cuz the structure is so damn rigid by every measure & the body/interior is not nearly @ the same level of engineering/rigidity obviously. BTW - do you have stock tunnel plate? Swapping out for thicker one w/ heat shield made mine stiffer, corner flatter, quieter & cooler just FYI

The pano roof on my Raptor gets cleaned every 4-6 months vac up any debris in the rails, wipe down all the seals w/ moist rag, then use graphite or lithium grease on the rails & krytox on everything else

Bout ready to do it now actually since pollen seems to have finally stopped up here in MA
 

greatone99

Full Access Member
Joined
Aug 2, 2019
Posts
785
Reaction score
356
Location
ma
so grease the fixed rear panel from the outside of the truck ? may try this as I grease the moving portion and still have a slight rattle from what seemed to be behind the driver seat
 

Cornwallis

Full Access Member
Joined
Apr 13, 2020
Posts
158
Reaction score
108
Location
L.A.
I'm going to try this...I have a slight rattle that I thought was behind the rear seat but now I think it's this. This forum is awesome for these types of things.
 

zemuron99

Full Access Member
Joined
Jan 23, 2018
Posts
384
Reaction score
382
Location
Seattle
F

Fixed it by loosening four of the six screws that hold it in place. Just a little. Then slighty repositioning the panel up and down a tiny bit but making sure it was put back exactly where it was. Also, I lubbed the rubber seal with some of that special lube.

OK, so I'll admit I haven't even gone out to eyeball my rear glass, but are the screws on the inside or outside? Someone else mentioned a t-25 bit, is that correct?

Thanks, I sometimes get a 'knock' at slower speeds (<40 mph or so) coming from the rear drivers side, this could be the source. ALmost sounds like the seat belt buckle is lightly knocking into the plastic on the door but I know that's not it.
 
Top