What did you do to your Raptor today? (Gen2)

[CVP33]

Offered $7…..accepted.

Rear Seat Release Strap Latch Kit For Ford F-150 2009-18 F-250 F-350 2017-19 US | eBay

2017+ F-250 and F-350 Supercab and Supercrew: These models will utilize a single kit on the driver's side. a simple and robust solution to accessing the area behind the rear seat backs in your 09+ Ford F-150 Supercrew, 15+ Ford F-150 Supercab, or 17+ F250 and F350.

www.ebay.com

 

[Old-Raptor-guy]

Offered $7…..accepted.

Rear Seat Release Strap Latch Kit For Ford F-150 2009-18 F-250 F-350 2017-19 US | eBay

2017+ F-250 and F-350 Supercab and Supercrew: These models will utilize a single kit on the driver's side. a simple and robust solution to accessing the area behind the rear seat backs in your 09+ Ford F-150 Supercrew, 15+ Ford F-150 Supercab, or 17+ F250 and F350.

www.ebay.com

Built rite knock off.
Either way that is about all it is worth. You can't really fit anything behind the seat and to get it to relatch is kind of a pain in the ass.

 

[xturdfergusonx]

96 bolts, a ton of anti-seize, and a sore back later. "New" wheels installed!!!

 

[julien194b]

Home made mounts, still need to wire.
First drain for my catch can, trimmed plastic my tire was rubbing on during u turns and tried to hunt down a rattle I get at low speeds with no luck.

Also just installed Cobb ap tcm stage 1 91, does anyone know what setting I should be watching for the intercooler temps?

View attachment 451764View attachment 451765

After all that, time for you to have a big intercooler, it could be better considering your tune engine and that now with lights , may intercooler don't catch enough air , don't you think so ?

 

[fordrat]

I changed the oil yesterday at my sons house and after we jacked up the truck so we could inspect the brake pads, he had a floor jack and we still had to put a 4x4 of block of wood to get it off the ground so today I thought I’d fix that problem. So I got underneath the truck to take some measurements so I could make an extension from the frame to the jack so it doesn’t max out of height and I looked at the rear to the axle and found it was discolored meaning wet, not dripping or anything but was leaking. I thought the axle was a one piece cast like what I was used to but I guess not because the passenger side was totally dry so my question is, is there a seal that I have to replace or can I just seal it with something else I don’t want to take it to a dealer and not sure if it falls under a warranty item I just hit 40,000 miles any suggestions would be appreciated thanks

 

[downforce137]

I changed the oil yesterday at my sons house and after we jacked up the truck so we could inspect the brake pads, he had a floor jack and we still had to put a 4x4 of block of wood to get it off the ground so today I thought I’d fix that problem. So I got underneath the truck to take some measurements so I could make an extension from the frame to the jack so it doesn’t max out of height and I looked at the rear to the axle and found it was discolored meaning wet, not dripping or anything but was leaking. I thought the axle was a one piece cast like what I was used to but I guess not because the passenger side was totally dry so my question is, is there a seal that I have to replace or can I just seal it with something else I don’t want to take it to a dealer and not sure if it falls under a warranty item I just hit 40,000 miles any suggestions would be appreciated thanks

the tubes are pressed into the housing.. the only real fix is to weld them in...

 

[fordrat]

Okay thanks I thought about maybe a sealant but now since it’s something like that and there not meant to come out maybe JB weld

 

[mattl600]

Installing this exhaust today. More clearance for the suspension.

 

[nikhsub1]

Installing this exhaust today. More clearance for the suspension. View attachment 452486

Bruh, just have straight pipes come right off the turbos out the hood. That'll give you clearance

 

[Thatblackraptor]

Installing this exhaust today. More clearance for the suspension. View attachment 452486

Let us know how you like it!

I made a video of their downpipes and exhaust setup. I ran both the axle dump and rear bumper exit setups. I found that the drone was a little too much for my taste.