Gen 3 Arrived and just Ceramic Coated DIY

[Ron Lanza]

What do you have up front for the level?

Eibach Springs up front & ProRyde 3 in 1 kit in the rear. Rides better then factory!! The springs alone put the front 1/2 higher the the rear, That was not the look I wanted. So I did the ProRyde 3 in 1 and went 1'' in the rear and it sits perfectly level now.

 

[Torchy]

This happened to me! I felt my plastic was prepped properly and I used CarPro eraser before I applied. You're right though. Once it's on and turns white it's near impossible to get off. I reached out to CarPro (Sky's the Limit) and was send the Ultima Tire and Trim. It was a nice gesture, but I wish you could see my cost for replacing all of the plastic bedside caps and other trim (NOT CHEAP). My instruction booklet for CarPro DLux didn't say anything about not applying to textured plastic. Maybe it has been revised since. I still have it.

CarPro DLux Ruined my Plastics

My truck has less than 5K on the odometer. When I bought it I decided to ceramic coat the paint and while at it I decide to protect the plastic black trim. I never thought it would ruin my plastics the way it did. I've tried using a bunch of products and nothing has worked. I asked CarPro and...

www.fordraptorforum.com

Interesting. Literally never had this happen. I do think they've always been new every time I've done it. Of course with good prep too.

How long did it take for them to show whiteness? My gen 2 was done the same way from new and looked fantastic for the 1 year I had it.

And no never seen his vids but I'll check them out. I have heard of obsessed though.

 

[Torchy]

I’ve always loved detail step by step write ups like this. Beautifully done

Thanks it's holding up strong. Had a car in front of me the other day use their washer fluid and it went all over my hood. I just watched it all bead off the hood at 70mph. Was pretty cool.

 

[RubyDaCherry]

Eibach Springs up front & ProRyde 3 in 1 kit in the rear. Rides better then factory!! The springs alone put the front 1/2 higher the the rear, That was not the look I wanted. So I did the ProRyde 3 in 1 and went 1'' in the rear and it sits perfectly level now.

I figured since the front looked higher than usual, why didn’t you go with Deavers springs in the rear to level out the Eibach’s up front? Just curious.

 

[Kotykb]

Looks like you're an OG fan like me.

 

[MDJAK]

Love Matt’s custom setup. Truck looks great, OP

 

[TheSkinMusket]

Since I can't take the Raptor through a carwash, I have a perfect excuse to order a bunch of new OG gear this spring.

 

[beachz]

Looks like you're an OG fan like me.

I am on a well. While we have great quality water, I could still use a filtration system. What is that system and how well does it work?

I was able to zoom in enough see that it is a Sptoless.

 

[TheSkinMusket]

I am on a well. While we have great quality water, I could still use a filtration system. What is that system and how well does it work?

I was able to zoom in enough see that it is a Sptoless.

Kranzle K1622TS Custom Install Solution

The Kranzle K1622TS Custom Install Solution is an excellent option for your car detailing needs. This is great for people who don't have access to a 20-amp circuit. I've put together everything you need including accessories to make this the best pressure washer experience in the market.

www.obsessedgarage.com

Welcome to the rabbit hole

 

[Ron Lanza]

I figured since the front looked higher than usual, why didn’t you go with Deavers springs in the rear to level out the Eibach’s up front? Just curious.

$$$$$ I think it rides perfect with he setup I did. But in reality, I guess i will never know if it would have rode better with deavers??