Rear up travel.

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

OP
OP
2012SCSVT

2012SCSVT

Full Access Member
Joined
Jun 30, 2021
Posts
110
Reaction score
185
Location
CA
Okay, so checking the clearance with the tires it looks like this will work okay. Just enough clearance at full bump.

It will probably rub when it's flexed left or right but I'm just going to go with the cut as needed technique one the truck is being used.

Ground clearance at full bump with full tire diameter is 7.5" so maybe 3 inches with the side wall compressed.
 

Attachments

  • 1000003625.jpg
    1000003625.jpg
    276.4 KB · Views: 46
  • 1000003626.jpg
    1000003626.jpg
    167.7 KB · Views: 38
  • 1000003623.jpg
    1000003623.jpg
    189 KB · Views: 46
  • 1000003630.jpg
    1000003630.jpg
    192.5 KB · Views: 48
  • 20231119_094353.jpg
    20231119_094353.jpg
    230.6 KB · Views: 48

Gumby

FRF Addict
Joined
Mar 7, 2023
Posts
1,860
Reaction score
3,556
Location
Nashville
@2012SCSVT
LOL Shot taken and received....LOL BUT your new and I have seen some really STUPID stuff in my life. You obviously have a clue.... A Real Good Clue. Carry on.... My Bad.
 
OP
OP
2012SCSVT

2012SCSVT

Full Access Member
Joined
Jun 30, 2021
Posts
110
Reaction score
185
Location
CA
Haha I wouldn't say I have a clue! Honestly, despite the fact that unpacking a leaf is just about the only way to set up bump if you are doing something custom, it's such a PITA that very few people do it.
 
OP
OP
2012SCSVT

2012SCSVT

Full Access Member
Joined
Jun 30, 2021
Posts
110
Reaction score
185
Location
CA
Oh. Damn hahaha I suck! Got my parts back from Lazer and drew my shock mount with a 2.25" axle instead of a 3.25" axle.

I did actually measure twice just didn't check my fat stupid fingers!

Anyway the frame gussets look like they will do nicely to build off the frame.

Sent in a revised drawing to the shock mount.
20231122_144832.jpg20231122_145520.jpg20231122_144522.jpg20231122_150430.jpg20231122_144556.jpg
 

Nex

RIP CoronaRaptor
Joined
Sep 2, 2021
Posts
8,628
Reaction score
24,785
Location
Washington State
Raptor swap going down on my 82 f250 with all the take off parts. Don't worry I won't run a single leaf with a sanded down 2x4 spacer on this truck either...

Why you are done here, my 96 could use some front tow hooks... Just saying...

:hidesbehindsofa:
 
OP
OP
2012SCSVT

2012SCSVT

Full Access Member
Joined
Jun 30, 2021
Posts
110
Reaction score
185
Location
CA
Oh yeah also I really want to put the spare back under the bed. Seems like it will clear the 37 so long as I end the exhaust prior to the axle... 1000003702.jpg1000003703.jpg1000003704.jpg
 

Attachments

  • 1000003705.jpg
    1000003705.jpg
    243.3 KB · Views: 6
  • 1000003700.jpg
    1000003700.jpg
    137.9 KB · Views: 6

Nex

RIP CoronaRaptor
Joined
Sep 2, 2021
Posts
8,628
Reaction score
24,785
Location
Washington State
No sketch.

You will also want to think about departure angles with the spare under the bed. Hate for you to runn through all this for a few more inches of travel to get ripped apart due to hanging up on your spare.
 


Write your reply...
Top