Search results

I do agree with you, and my reason for unplugging all of the motors. I was hoping someone would have had the same issues as me. Again, I can remove every motor and still get the popping. It sounds like it is coming from the large box behind the glove box which I think is called the plenum...

Put everything back together with a new blend door behind radio, did fuse reset to recalibrate more than 10 times, and still have popping :(:mad:

Reviving my own post from the dead. I am still battling this today! It just turned cold here, and I replaced the actuator behind the radio yet again only 2 months ago. Yesterday driving to work I was getting warm from the driver vents and freezing cold from passenger and rear vents. The full...

If you do the fuse removal reset does yours actually calibrate when you put it back in? Mine makes no moves or sounds when I try it. I tried unplugging the battery for 30 minutes as well and nothing.

I am to the point I don’t have a clue what my issue is. Possibly the gear in the plenum has lost its home spot and tries to go too far, pops a few times, and doesn’t do it again until the truck is off and started again. If I do temp above 82 I hear it strain but no pops. Temp goes up and down as...

I replaced the first one with a amazon special, and then it persisted and got worse so replaced with a factory one again. I took the 2nd one out and actually took it apart to see what was going on and 1 of the gears was shredded down. At that point if it went in it clicked constantly, put the...

No one :(

So replaced my passenger side (upper) blend door actuator since I had the famous clicking/knocking, and mine actually was constant and never stopped. After I replaced it I still get a few clicks once I start the truck and then it stops. AC and heat work how it should and have both. Any ideas of...

Looks like maybe I didn't get the plug completely snapped in, and it worked its way loose :(

Hey all. just had issues with the truck yesterday and came to a conclusion through getting code P1450 that I needed to replace the evap purge valve. I just completed that, cleared the code/s, and went for a drive. I went ahead and filled it up with fuel, and when I restarted the CEL came back...

Sorry I haven't had a chance to dive into this yet unfortunately.

Thank you for the confirmation on the part numbers. I did a good amount of research and youtubing already! I am a Gen 1 so also good to know. I will check through all of the fuses while having a beverage, and then unplug the battery, and have another. Then go from there.

Having an issue where all air and heat comes through the dash front facing vents. It doesn't matter what setting I put it all, everything is blowing straight to the cabin. Nothing on the feet, or windshield. I have read it is known the actuator goes bad, but when I try to make it "click"...

Confirmed. Awesome lineup!

Didn't get a chance to clean up the starter this weekend. Priority of winterizing the boat took over. Hopefully be able to look at it Wednesday. I have no codes.

thank you both. fuse 27 looked perfect and really brand new. the relocation had not been done either. when i replaced the battery i cleaned everything and added the little felt pads too. i will check the starter tomorrow and clean that up. if that doesnt work it should be the vapor canister...i...

In for that answer too since I think I am coming up on this issue.

Thanks! Not sure how I didnt find the fuse27 deal. Where is the best place to buy the TSB kit from? Or just cut and solder in the new spot?

Yes 2011 6.2L. I will do that tonight.

Focus RS pics or you don't actually own it ;)

This started about a month ago, and has slowly gotten worse. First start of the day, and if it sits for a couple of hours it is very slow to crank and start. The only solution I found was to turn the key to the ON position (not trying to turn it over), waiting 10 or more seconds, and then it...

So ended up coming out of a store 2 weeks ago and my rear bumper was knocked in. Someone hit it and drove off. Truck is in the shop and having the camera looked at too. Let you know if they say anything that is worthy or if they just replace it.

Wish you were closer :(. Someone was nice enough to hit my rear bumper last week and need one.

Sorry haven't been on here in a bit, and have not had time to troubleshoot yet. It has to be something in the signal/wiring. Mine is completely done and does not ever see anything. Randomly 5 days ago it came on flashing and rotated, and never happened again. #1 buy that camera somewhere...

I will do that. It has stayed black for the passed almost week, and I get a pop up saying "no signal from backup camera". Last year I replaced the camera and it worked until this. Going to check the wiring deeper and message Noah. Thank you