Low mount light Bar featured on Ford Promo truck.

[Rick@FreedomMotorsports]

I feel silly for asking, but are these meant to be used on road or off road? If on road, are these DOT?

All off-road NON-DOT lights.

30" RDS
RDS-Series 30" - Spot Surface Cool White Black 30"... | Rigid Industries

2 E-Series 6"
E 6" - Flood Surface White Black | Rigid Industries

Capture Black Edition
Capture Black | Rigid Industries

Foutz is at around $2450, full retail.
PM me for the lights and I can save you a bunch.

 

[DiSanto]

I installed this today. Took about an hour. One small hole in stock bumper for each upper strut mount. The rest is simple.

Now to mount the lights. Hope I can figure out the wiring.

Any advice on that?

Thanks,
Dave

 

[NJSP117]

Great looking bar. I've started to look for something to add some lights to the front. Love this one....but wow, $900 for just the bar is crazy. I could see 400 or maybe $450, but $900??....dam. And $2500 with the lights...SMH, I'd rather pick up a whole new bumper from ADD...just my opinion....

 

[SilentShooter]

I installed this today. Took about an hour. One small hole in stock bumper for each upper strut mount. The rest is simple.

Now to mount the lights. Hope I can figure out the wiring.

Any advice on that?

Thanks,
Dave

Wiring will be real easy you just tie into the upfitter wiring.

 

[Rick@FreedomMotorsports]

Great looking bar. I've started to look for something to add some lights to the front. Love this one....but wow, $900 for just the bar is crazy. I could see 400 or maybe $450, but $900??....dam. And $2500 with the lights...SMH, I'd rather pick up a whole new bumper from ADD...just my opinion....

Welcome to what a bumper cost for a Raptor. And you think an ADD bumper with Rigid lights will be cheaper? Maybe because there might be a choice for only 1 light bar.

I will be more than happy to sell an ADD bumper with lights to any GEN2 owner for a lot less than what you can get from ADD themselves (they usually only offer 5% off). And I already stated that I can save anyone some serious money on those 4 lights. Good lights are not cheap and ****** lights are cheap. If you want it for show, get cheap. If you really want to use the lights when off-roading, don't cheap out. I prefer Baja Designs over anything else but this bumper is designed for Rigid so I would stick with that.

PM me for a quote.

 

[byrdawg]

Does this effect the front camera and sensors?

 

[pughde]

I installed this today. Took about an hour. One small hole in stock bumper for each upper strut mount. The rest is simple.

Now to mount the lights. Hope I can figure out the wiring.

Any advice on that?

Thanks,
Dave

Did the rubber around the tow hooks create any problems. I am not sure how to work around them when installing a bar. How did you remove them? Did you put them back on?

 

[DiSanto]

Did the rubber around the tow hooks create any problems. I am not sure how to work around them when installing a bar. How did you remove them? Did you put them back on?

the rubber was tossed. no need for it.

---------- Post added at 07:07 PM ---------- Previous post was at 07:06 PM ----------

Does this effect the front camera and sensors?

haven't noticed any issues

 

[TMAC3]

the rubber was tossed. no need for it.

---------- Post added at 07:07 PM ---------- Previous post was at 07:06 PM ----------





haven't noticed any issues

I like the set up.

1. Is it possible to show a picture of the front camera view?

2. Do the lights extend past the bar? Can you take a picture of the side angle.



Sent from my iPad using Tapatalk