GJ Motorsports 3rd Brakelight

[1BAD454SS]

Got Antenna connected to radio Saturday morning ,the 3rd brakelight comes with good quality coax and connector, I shortened my cable to the length i needed and installed a new connector. Checked SWR this morning 1.2 ratio at 109 watts transmiting power. Anything below a 1.5 ratio is excellent . 1.5 to 2.0 is good. Higher than that not so good. be sure if you have excess coax you don't coil it up. Cut it to length and install new connector or stretch it out under the carpeting or inside the panels . Its also a Good idea to have your SWR checked after installation .

 

[14 BlackScrew RR]

Tracking shows that mine should be delivered today. I went with the S2 Pro amber driving/combo left and right, and the S2 Sport white work/scene for the center.

Now if I could just get @t_j to reply to my PMs on some other work I need GJM to do...

>>> Now if I could just get @t_j to reply to my PMs on some other work I need GJM to do... <<<

I wish you LUCK!

TJ is Notorious about not keeping his word.
I'm speaking from experience.
I spoke to TJ over the phone a little over 3 weeks ago in discussion about ordering a set of Deavers springs with powder coat, an Icon bump stop, and the 3rd brake light.
During our discussions, I requested the he send me an invoice, so I could forward the funds to pay for these items.
In our discussions, I also reminded him that very soon I'll be going ahead with the rest of the mods of a complete set of Icon 3" shocks, both front and rear.
All in all, this is well in excess of over $10,000.00 in just parts.
To my dismay, I've yet to hear back from TJ, nor have I seen the Invoice as yet. (No! It's not in my spam folder either)
And! I must say, this is not the first time he has been tardy in getting back to me in regards to business.
Guess he is too busy to reply!!!!!!!!!!!!!!

 

[NE Ford]

Tracking shows that mine should be delivered today. I went with the S2 Pro amber driving/combo left and right, and the S2 Sport white work/scene for the center.

Now if I could just get @t_j to reply to my PMs on some other work I need GJM to do...

TJ has been out of the country since the 27th and won't be back until this weekend. Please shoot me a direct message to discuss the other work you need done.

 

[Clockton]

I have had issues with the light pulling loose from the cab with the OEM hardware. I sent a note to GJ describing the problem a few weeks ago and thought that I was on my own to find a solution. Today in mail arrives a note saying they had reports of the retaining clips being pulled out of the back of the cab and sent new hardware for use with the light to replace the OEM hardware.

Good stuff GJ.

Thanks

 

[t_j]

I have had issues with the light pulling loose from the cab with the OEM hardware. I sent a note to GJ describing the problem a few weeks ago and thought that I was on my own to find a solution. Today in mail arrives a note saying they had reports of the retaining clips being pulled out of the back of the cab and sent new hardware for use with the light to replace the OEM hardware.

Good stuff GJ.

Thanks

Everyone that ordered an NMO mount got replacement hardware. If you are having a problem with a none NMO light and the clips shoot us an email/pm/fb/call and we will ship you out some hardware.

 

[Mspeed]

I need help with pick out an antenna for my set up. I just purchased an icom 2730A dual band radio. I plan to install it in my chase rack. I'm looking for the longest range size don matter. Any ideas?

 

[Booth9999]

Hey t_j, need to buy a new seal for my GJ light. Had to take the light off to switch around the settings and it ripped. I left a email but i haven't heard back yet. any help would be great!

 

[renegadeagle]

Ordered the kit for my 2010 Raptor Received the kit for 2017 Raptor. Contacted 4x4 Truckleds and told me to send back everything including harness. Now received correct assembly but the connector on harness does not plug on truck.Attached photos.Almost a month between all this odysey .All the routing of cable done on truck already.Very frustrating.
For the money would have expected honestly better customer service.

Truck connector,original from OEM
to original brake light, on left 3 pins.Harness connector on right.4 cables and connector does not plug to truck.

 

[TAURUS]

The connector that you need to plug into is further back in rear headliner. We ran into same.

 

[Chiefapple]

Yup. Reach further up into the headliner. It’s there. It’s attached to the roof.


Sent from my iPhone using Tapatalk