Search results

I've revised the following item on my BCM spreadsheet to include the bold notes below it: 726-26-01 xxx* xxxx xxxx - Ambient Light Sensor Type Cfg: 0=Slow_FNA, 1=Fast_Row 0=15 seconds delay turning on headlamps when dark, 1=2 seconds delay turning on headlamps when dark I haven't looked to see...

No, nothing has been found for that or the other speed-restricted features. ---------- Post added at 03:47 PM ---------- Previous post was at 03:45 PM ---------- Most of the things for the '16 Super Duty here should work for a '13 Raptor...

This change in APIM: 7D0-02-01 5753 xxxx xxxx - Allows NAV in motion on Sync 3 v2.2-3.x, viewing/replying text messages & Sirius Travel Link still works. ** 911 assist will be disabled with this enabled ** Speed limit signs in NAV will look European after doing this but the speed listed will...

Cause that's not how the extended play works. After the 10 min timeout (or when you first get in the truck) just press the volume button without turning on the truck at all (even accessory position) and the stereo will come on and stay on for 60 mins.

No, that just enables whatever value set for placard tire pressure in BCM actually displays in the TPMS screen in the cluster showing what the specified tire pressure for front/back should be. Drive around the block until the numbers show in TPMS and you should be good.

BCM 726-40-01 xxxx **xx xxxx TPMS Placard Front Tire Pressure (convert p.s.i. to hex) 726-40-01 xxxx xx** xxxx TPMS Placard Rear Tire Pressure (convert p.s.i. to hex) Examples: 726-40-01 xxxx 1E1E xxxx - 30 psi front & back 726-40-01 xxxx 2323 xxxx - 35 psi front & back

It's because of the tune, you'd have to return the tune to stock to be able to use FORScan and then put the tune back on after you're done with FORScan. Some tunes change the PCM VID block and that prevents FORScan from recognizing the vehicle.

No, haven't seen any issues. Did your existing license expire before you tried to load the new license? Disconnecting the battery won't reverse any FORScan change and unless the dealership specifically loads as-built to a module, the changes will remain also. Normal service work won't...

Yes and no. You'd have to change all the ambient LEDs to color changing ones and then you could enable it in FORScan and be able to change the colors like prior years had. There are some guys doing this in the 2nd half of this thread over here...

Not really. When they hook up to your truck with IDS they go to programmable parameters for the vehicle IDS is hooked up to and for the F150s there is no option in there for them to enable autofold mirrors or global windows like they would see on something like an Explorer. Ford didn't intend...

Did you reboot the computer after installing the driver? I've tested that same adapter using this driver: http://totalcardiagnostics.com.s3.amazonaws.com/CH340-USB-Driver.zip After installing the driver, reboot computer, plug in the adapter and then launch FORScan. In FORScan settings...

It depends on whether your system uses a DSP or not. For example mine is the Sony system so my value there in ACM says front tweeter disabled since the DSP is outputting the signal instead of the ACM. This is my understanding but I'm by no means any audio expert.

Not sure if it's different on '18 Raptors but on '15-'17 F150 the ANC=Fake Engine Noise 727-01-01 xxxx x*xx xxxx 0=FT absent & CS : North American & ANC absent & USB absent 1=FT absent & CS : North American & ANC absent & USB present 2=FT absent & CS : North American & ANC present & USB absent

Not that I'm aware of

That new IPC-new spreadsheet is based off of an Explorer and the auto re-lock you see there is for adding that to the menu settings but doesn't work on F150s. This alone wouldn't be required for it to work anyways because when you check/un-check boxes in the IPC menus it actually changes values...

It's something I've been looking into this past week and it would most likely require firmware change to FCIM and/or SCME module if possible; not just a simple FORScan value change. I'll be experimenting more with this in the coming week.

Phew...I was worried I was gonna get the private tour of the pit of misery :favorites13:

I've never had a '17 Raptor cluster plugged into my truck so I don't know what's different on an '18 Raptor cluster. There's a few differences on a normal '18 F150 cluster vs. '18 Raptor cluster. The new '18 F150 cluster has "Pre-Collision" instead of "Collision Warning" and for some...

I only had the Raptor cluster in my truck for a day before I sold it. Now I have a normal '18 F150 cluster installed that I'll keep in there. My newest project is getting the new 2018 Adaptive Cruise Control stop/go & pedestrian detection working in my '16. My truck already has ACC but I'd...

Nope, no way to do either of those things.

It means the following: in your cluster menu go to settings, adv settings, vehicle, lighting and select the box there that says "Daytime Lights". If you don't do this then you won't have any DRL function. You never had this option with your Canadian settings but with the changes you did you...

Yeah, make this change and leave it: 726-45-01 xxxx 7Fxx xxxx That will allow you to write any of the values below (half of them won't write and FORScan will give you an error if the 7F isn't set at 726-45-01) 726-50-01 108E 726-50-01 017F 726-50-01 0280 726-50-01 0482 726-50-01 0886 726-50-01...

FYI: I finally got the Raptor 8" cluster installed in my truck and tested it out for any additional menu items that could be added but didn't find any.

The 2014 F150 spreadsheet here should work: https://docs.google.com/spreadsheets/d/15MQ8CEh7eSXUJYjPg-J8uUqpLwP_xyqbfQHB0rAnXNs/edit#gid=1329872825 or the 2016 Super Duty spreadsheeet: https://docs.google.com/spreadsheets/d/17e_PIE5s3H266gWgSG7xdFLGKxIr1-K_RwrIx4qIAtI/edit#gid=882975515 The...

Lol Vegas!!!