You shouldn't be able to tell!
That's my almost finished wiring for the HID's the Duallys and the 20" Rigid...
That's my almost finished wiring for the HID's the Duallys and the 20" Rigid...
If I did this right...
- Thread starter AngryBird
- Start date
Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.
OP
OP
I just had to wait till it was dark so I could aim the Bar. I'm putting them back on here in a sec.
HIDs + Duallys...
______________
HIDs + Duallys + 20 E-Series shined at tower 101 yards away (measured w/ Laser range finder):
________________
HIDs + Duallys + 20 E-Series shined across a canyon. At 237 Yards away.
---------- Post added at 08:49 PM ---------- Previous post was at 08:47 PM ----------
Thanks! Looks meaner without em anyways lol...
HIDs + Duallys...
______________
HIDs + Duallys + 20 E-Series shined at tower 101 yards away (measured w/ Laser range finder):
________________
HIDs + Duallys + 20 E-Series shined across a canyon. At 237 Yards away.
---------- Post added at 08:49 PM ---------- Previous post was at 08:47 PM ----------
Had to laugh at the missing plastic on your bumper. Look at mine.
Nice wiring job
Thanks! Looks meaner without em anyways lol...
Last edited:
vanilla_gorilla
FRF Addict
Yeah, i made the mistake and ripped mine off too, now i have to buy a new one. Any advice on how to put them on/off without removing the entire bumper? I can only get to one of the bolts for the bumperette thing.
MagicMtnDan
FRF Addict
The bumperettes SUCK! If they weren't handled nicely at the plant the tabs can make the bumperette difficult at best to re-install.
I tried everything including using a set of pick tools (smaller than awls with different ends on them) to pull the tabs out when I was re-installing the bumperettes. At the end of the day I gave up on one of them and actually had to drill a small hole through the underside of the bumperette (underneath it where it's hard to see unless you're on the ground looking up at it) and then put a screw in the hole to get the bumperette to stay securely in place.
I tried everything including using a set of pick tools (smaller than awls with different ends on them) to pull the tabs out when I was re-installing the bumperettes. At the end of the day I gave up on one of them and actually had to drill a small hole through the underside of the bumperette (underneath it where it's hard to see unless you're on the ground looking up at it) and then put a screw in the hole to get the bumperette to stay securely in place.
Boss Hoss
FRF Addict
Nice throw there... Should be able to see where you are going!
OP
OP
Boss Hoss said:
Yeah its the brightest light I've seen on the front of a vehicle...
Similar threads
Members online
- RdR2027
- EastEndAngler
- c_landd
- Shane361
- MORaptor1
- kylesatx
- Abdulazizfd
- Dudebrodude
- CleverGirl_
- rapidredOMF
- therapture62
- Spike Spiegel
- brunorulez
- MaTm
- Gdog
- Luke0331
- BHook
- Sharpie69
- kocher93
- Burke242
- wweaver
- Jhollowell
- icecoldak
- Jmeo
- MacK88DO
- lsirois
- HAP
- tcm glx
- jwheat1
- Braaaaptor
- Gr8-19SC
- P4SHOCAT
- fat tony
- someday
- Barrymahcockiner
- grillcheeseRaptor
- AARaptor
- ReallyNice
- UtzPotatoChip13
- LA_Raptor
- EL Snagadore
- rushneck
- ofcbarbrady
- FullSend
- letsgetthisdone
- Raptor406
- Pacifico66
- thatJeepguy
- MurderedOutSVT
- PK37
Forum statistics
Latest posts
-
-
-
Raptor R realistic fuel economy expectations
- Latest: Dudebrodude
-
