What did you do to your Gen 3 today?

[cdiddy4224]

Yesterday I finally decided to install my triple fogs lights I orders back in March. Not a difficult install, just very time consuming. I think it took me 4-5 hours. Electrical was straight forward, aligning the fogs on the brackets was a pain in the ass. As far as orientation, I have them setup:
Inner most location: SAE fogs
Combo Driving/Flood in the middle
SAE Yellow fogs on the outer most location.

I tested them last night and I'm impressed. The Combo lights def. throw light down range for how low they are. The fogs are aimed lower and do just fine. The yellow fogs, I'll test those when we get snow. I will say the powder coating on these is delicate (I believe I read that the powder coating on these wasn't as strong as BD), I scratched one fog while installing.

 

[jajones45]

I added “Rugged Rear Wheel Well Liners” to the beast.

These liners blackout and protect the rear wheel well. I did it for the aesthetics and am very pleased with the outcome.

 

[m4can2]

I added “Rugged Rear Wheel Well Liners” to the beast.

These liners blackout and protect the rear wheel well. I did it for the aesthetics and am very pleased with the outcome.

View attachment 361868
View attachment 361867

Link to the liners?

 

[jajones45]

Rugged Rear Wheel Well Liners WWF15021 | RealTruck

WWF15021 Rugged Rear Wheel Well Liners is on sale at RealTruck with a Low Price Guarantee and free shipping! Check out specific images and videos to make the perfect buying decision.

realtruck.com

 

[Littlefx4]

I added “Rugged Rear Wheel Well Liners” to the beast.

These liners blackout and protect the rear wheel well. I did it for the aesthetics and am very pleased with the outcome.

View attachment 361868
View attachment 361867

That looks nice man. How long was the install? Did you have to remove anything?

 

[m4can2]

Rugged Rear Wheel Well Liners WWF15021 | RealTruck

WWF15021 Rugged Rear Wheel Well Liners is on sale at RealTruck with a Low Price Guarantee and free shipping! Check out specific images and videos to make the perfect buying decision.

realtruck.com

Thanks man. How was the install and fitment?

 

[Bullet Bob]

When I checked the website, it shows that the liners fit a 2021, but not a 2022. Must be different?

 

[jajones45]

I have a 22’ raptor and they fit well. I am not the type that buys without validating figment for the truck so I must have confirmed with the chat function.

Getting them in is a little trickier than expected.

You have to remove 6 screws that hold the fender in place (it says remove all 8 but there is no need to remove the 2 bottom screws on each side) so that you can slide the liner in between then retighten.

Getting the liner in is a tight fit but I didn’t need any tools. I used my fingers and some logic on how to bend the plastic to slip it in.

First wheel took 30 minutes, second under 15 minutes. It’s one of those mods that when you’re done you say “should have come from the factory like this”.

 

[Bullet Bob]

I have a 22’ raptor and they fit well. I am not the type that buys without validating figment for the truck so I must have confirmed with the chat function.

Getting them in is a little trickier than expected.

You have to remove 6 screws that hold the fender in place (it says remove all 8 but there is no need to remove the 2 bottom screws on each side) so that you can slide the liner in between then retighten.

Getting the liner in is a tight fit but I didn’t need any tools. I used my fingers and some logic on how to bend the plastic to slip it in.

First wheel took 30 minutes, second under 15 minutes. It’s one of those mods that when you’re done you say “should have come from the factory like this”.

Thanks for the advice. I'll be doing this next.

 

[Littlefx4]

Thanks for the advice. I'll be doing this next.

Let us know how it goes @Bullet Bob!