Search results

  1. figure1a

    Need help for Forscan code

    Oh, chit...
  2. figure1a

    (4) Ford 150 Raptor Wheels Gen 3 Beadlock Capable 17 X 8.5 Wheels with KO2 Tires

    Oh chit. Always forget that part. $1200 local pickup only.
  3. figure1a

    (4) Ford 150 Raptor Wheels Gen 3 Beadlock Capable 17 X 8.5 Wheels with KO2 Tires

  4. figure1a

    (4) Ford 150 Raptor Wheels Gen 3 Beadlock Capable 17 X 8.5 Wheels with KO2 Tires

    Ford 150 Raptor Wheels taken off my 2021 Gen3 Raptor. These are the Beadlock Capable 17 X 8.5 Wheels with BF Goodrich KO2 All Terrain tires. Tires are 35" (315/70R17). Bolt pattern is 6x135. Offset is +34. Taken off my truck at 25,000 miles and the tires are rated for 50,000 miles so probably...
  5. figure1a

    What did you do to your Gen 3 today?

    Don't think so. Pipes exit right above the rear axle. Truck still sounds like I got a Dodge Charger but couldn't afford to get the V8 so I got a V6 and put some fart cans on it—so you are good to go there.
  6. figure1a

    What did you do to your Gen 3 today?

    You can actually remove your pipes after the muffler without making any cuts. All bolts. Then add some turn downs and point them out so you don't cook your spare. If you were to also remove the spare, you will gain a few degrees on departure angle with both the pipe tips and spare gone.
  7. figure1a

    High Speed Off Road & OEM Spare Tire Location

    Most people just move it to look cool. These are same people that drive around with MaxxTraxx boards strapped to their roof 365 days a year even though they only off-road 3 days a year. Some people move it because they find it easier to get to the spare in off-road conditions when it's in the...
  8. figure1a

    What’s going on here? Middle mud flaps?

    Someone else posted a while back on putting mud flaps on the running boards like that and pretty much got flamed because 1) it looks DAF 2) a single off-road trip will surely snap them off and 3) it's a focking truck and if you use it like a truck you're going to get some roost marks on the rear...
  9. figure1a

    Reminder - Check your front brake lines

    The TSB said trucks built before 14 June 2021.
  10. figure1a

    Reminder - Check your front brake lines

    Pretty sure that's how you rotate radials unless you have some uneven wear.
  11. figure1a

    Gen3.5 specific forums?

    Yeah, 3.1 was the dual digital temp knobs delete. Correct on the 3.1.1 with the heated steering wheel undelete. Can't wait for those subforums so we talk about it.
  12. figure1a

    What did you do to your Gen 3 today?

    I dunno: 1) I think they would be snapped off every time you went offroad 2) Rock chips, etc. down there—it's a focking truck.
  13. figure1a

    Baja Designs Linkable Bumper Light Kit & Triple Fog & Upfitter Relay Box & Camera Relocate Install

    For the Baja Squadron Pro fogs and driving lights, I just used the factory Ford connectors and those lights do not go through relays. Those 2 circuits (factory fox switch and Aux1) have not blown fuses powering the Squadron Pros so I just left them directly wired. So Relay #1 in my relay box is...
  14. figure1a

    Am I just being too particular?

    Raptors are $100,000+/- vehicles but at the end of the day they are still Ford's and pickup trucks. Just because we paid a lot for them does not mean you are going to get the fit and finish of a German car.
  15. figure1a

    Touch Up Paint Beadlock Beauty Ring

    Just leave it. Also, if that remains the only mark on your truck, you are not using it right.
  16. figure1a

    Baja Designs Linkable Bumper Light Kit & Triple Fog & Upfitter Relay Box & Camera Relocate Install

    No heat issues. Been out in Borrego with it. My printer prints at 500˚F with carbon fiber—same printer that NASA, US Army, Ford, etc. use. Pretty sure since all the other plastic in my engine compartment isn't melting, my parts will be just fine. If you think about it, you can pop your hood...
  17. figure1a

    What did you do to your Gen 3 today?

    I like the idea of deleting the tail pipes. Is there any reason that I couldn't do the same but just further up after it comes out of the muffler? I don't want to cut and there is a joint right after the muffler where the pipes go from three back to two. Just clamp on the turn downs there? Also...
  18. figure1a

    What did you do to your Gen 3 today?

    Camera relocate kit will fix all that camera blockage
  19. figure1a

    Baja Designs 2021+ Gen3 Ford Raptor XL LINKABLE BUMPER LIGHT KIT w/ XL80 Upgrade

    Sold
  20. figure1a

    Did the ADD Phantom front bumper

    You can see in the pics the match. Not sure any other powder coat would be closer. Certainly, don't do gloss black as the flares are not gloss and are not black.
  21. figure1a

    Baja Designs Triple Fog Lights w/KR Off-Road Brackets 2021+ Gen3 Ford Raptor

    Baja Designs Triple Fog Lights w/KR Off-Road Brackets for 2021+ Ford F-150 Raptor. This includes: + 6 Baja Designs Squadron Pro Lights (4 Driving Combo, 2 Spot) + 2 KR Off-Road Brackets to fit all 6 lights in your Gen3 Raptor stock bumper fog light banks + 6 Brackets that let the lights mount...
  22. figure1a

    Baja Designs 2021+ Gen3 Ford Raptor XL LINKABLE BUMPER LIGHT KIT w/ XL80 Upgrade

    Baja Designs 2021+ Ford Raptor XL LINKABLE BUMPER LIGHTS. This includes: + Baja Designs Linkable Light Pods light bar + SPV Specialty Performance mounting brackets + Nine Volt camera relocate kit (you will want this if you install any lightbar on your front bumper) + Upgraded two of the XL Sport...
  23. figure1a

    Spare tire safety cable removal *added photos of cable in later post *

    Your spare does not fit under the truck?
  24. figure1a

    Did the ADD Phantom front bumper

    ACC relocate works fine for me. Used the ADD new version (there is an old version that gave people issues). I don't see why you couldn't use the ADD bracket as it is not dependent on the bumper at all. Also, on the ADD bracket make sure the connector for the module is fully seated. If you...
  25. figure1a

    Did the ADD Phantom front bumper

    Stock rigid lights came off long ago. The sides have 10" Rigid light bars and the middle is a 20" Rigid. The ACC module is relocated up into the grille.

Staff online

Members online

... and 12 more.
Total: 2,402 (members: 62, guests: 2,340)

Forum statistics

Threads
95,463
Posts
2,008,978
Members
59,070
Latest member
Asqrd
Top