Forums
New posts
Search forums
What's new
New posts
New profile posts
Latest activity
Members
Registered members
Current visitors
New profile posts
Search profile posts
Log in
Register
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
RAM TRX - TRX-Forum.com
Bronco Raptor - BroncoRaptorForum.com
Forums
GEN 2 (2017-2020) Ford F-150 Raptor Forums
Ford F-150 Raptor General Discussions [GEN 2]
800A+ Offroad Build
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="Bark beetle" data-source="post: 1137913" data-attributes="member: 21513"><p>I finally got the wiring done for the winch, painted the front skidplate and silver part of the bumper and tested out the winch wire connections. Headache rack and bed rails are planned for tomorrow.</p><p></p><p>All stealth wiring because I don't use the winch that often. Stays under the hood until I need it.</p><p>[ATTACH=full]268437[/ATTACH]</p><p>[ATTACH=full]268438[/ATTACH]</p><p></p><p>Front mount, same for the passenger side as well</p><p>[ATTACH=full]268439[/ATTACH]</p><p></p><p>Extension cable to reach the back</p><p>[ATTACH=full]268440[/ATTACH]</p><p>[ATTACH=full]268441[/ATTACH]</p><p></p><p>The extension cable, jumper cables and the storage bags with the winch. Jumpers fit nicely behind the rear seat above the jack.</p><p>[ATTACH=full]268442[/ATTACH]</p><p></p><p>All cables were made by cv-supply on ebay. My Tacoma friend found him and he makes really nice stuff. This was a custom order I worked out with him that included the following:</p><p></p><p>1 - 24ft 4 gauge cable assembly with quick connectors and dust covers on both ends</p><p>1 - 4 ft 4 gauge cable assembly with quick connector and dust cover on one end and lugs on the other - from battery to front</p><p>1 - 4 ft 4 gauge cable assembly with quick connector and dust cover on one end and lugs on the other - from winch </p><p>1 - 20 ft 4 gauge cable assemby with quick connect on one end and jumper clamps on the other</p><p>2 - bucket boss jumper cable bags</p><p></p><p>If I did it again I might consider making the pigtails 6ft instead of 4ft.</p><p></p><p>I should also mention that winching with the stock cable mounted hand controller in the rear mount is a two person operation, it is too short to make it into the cab. A wireless setup will be in my future but most of the time there are at least two of us so it is a low priority.</p><p></p><p>Black skid looks much better and the receiver mounts blend in a lot better now.</p><p>[ATTACH=full]268443[/ATTACH]</p><p>[ATTACH=full]268444[/ATTACH]</p><p></p><p></p><p>Sent from my iPad using Tapatalk Pro</p></blockquote><p></p>
[QUOTE="Bark beetle, post: 1137913, member: 21513"] I finally got the wiring done for the winch, painted the front skidplate and silver part of the bumper and tested out the winch wire connections. Headache rack and bed rails are planned for tomorrow. All stealth wiring because I don't use the winch that often. Stays under the hood until I need it. [ATTACH=full]268437[/ATTACH] [ATTACH=full]268438[/ATTACH] Front mount, same for the passenger side as well [ATTACH=full]268439[/ATTACH] Extension cable to reach the back [ATTACH=full]268440[/ATTACH] [ATTACH=full]268441[/ATTACH] The extension cable, jumper cables and the storage bags with the winch. Jumpers fit nicely behind the rear seat above the jack. [ATTACH=full]268442[/ATTACH] All cables were made by cv-supply on ebay. My Tacoma friend found him and he makes really nice stuff. This was a custom order I worked out with him that included the following: 1 - 24ft 4 gauge cable assembly with quick connectors and dust covers on both ends 1 - 4 ft 4 gauge cable assembly with quick connector and dust cover on one end and lugs on the other - from battery to front 1 - 4 ft 4 gauge cable assembly with quick connector and dust cover on one end and lugs on the other - from winch 1 - 20 ft 4 gauge cable assemby with quick connect on one end and jumper clamps on the other 2 - bucket boss jumper cable bags If I did it again I might consider making the pigtails 6ft instead of 4ft. I should also mention that winching with the stock cable mounted hand controller in the rear mount is a two person operation, it is too short to make it into the cab. A wireless setup will be in my future but most of the time there are at least two of us so it is a low priority. Black skid looks much better and the receiver mounts blend in a lot better now. [ATTACH=full]268443[/ATTACH] [ATTACH=full]268444[/ATTACH] Sent from my iPad using Tapatalk Pro [/QUOTE]
Insert quotes…
Verification
Post reply
Staff online
Big Blue
Administrator
Members online
jAKe47
MarkOne
CleverGirl_
TwinscrollRepTar
Big Blue
wazatataza
Corsarych
WTX
Jmbeebe0722
roger7254
SuprSeb
Zeusmotorworks
Forum statistics
Threads
93,697
Posts
1,966,975
Members
57,001
Latest member
87KT
Forums
GEN 2 (2017-2020) Ford F-150 Raptor Forums
Ford F-150 Raptor General Discussions [GEN 2]
800A+ Offroad Build
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
Accept
Learn more…
Top