Forums
New posts
Search forums
What's new
New posts
New profile posts
Latest activity
Members
Registered members
Current visitors
New profile posts
Search profile posts
Log in
Register
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
RAM TRX - TRX-Forum.com
Bronco Raptor - BroncoRaptorForum.com
Forums
Ford Raptor Forums - General Information
Ford Raptor Recalls | TSB's | SSM's
TSB 11-4-7 - Third Brake / Cargo Light / High Mounted Stop Lamp TSB/SSM and Fix
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="BigJ" data-source="post: 136265" data-attributes="member: 62"><p>Been reading a lot lately about several folks discovering that their 3rd brake light is leaking. I've read that the results from that leak can range from no problems, to headliner staining, to hill decent control faults, ABS faults, to who knows what else. Bottom line? Ya really REALLY don't want that thing leaking.</p><p></p><p>Here's the SSM that deals with it</p><p>I've never had a problem, but mine was built before the SSM's cutoff date, so I figured I'd better be safe that sorry since I'm out of warranty. At a minimum Ford wants somewhere around $400 to replace the light (before labor!) and who knows what else to diagnose any other problems the leak caused. So I pulled it down and lined the edge with a bead of window and door silicone. I didn't find a how-to really, so I figured I'd make one just 'cause.</p><p></p><p>Here's what mine looks like before the fix. A little weird, but no water leakage that I can tell:</p><p>[ATTACH=full]186291[/ATTACH]</p><p></p><p>[ATTACH=full]186292[/ATTACH]</p><p></p><p>To pull it down, grab a #2 phillips screwdriver and slowly back out the two screws holding it in place</p><p>[ATTACH=full]186293[/ATTACH]</p><p></p><p>[ATTACH=full]186294[/ATTACH]</p><p></p><p>A quarter turn clockwise on each socket will free it from the housing, and a quick press to release the clip drops the LED connector. I didn't bother since its simple enough to apply the silicone with it up there, but if your housing is wet or dirty, ya might want to so its easier to dry out and clean up.</p><p></p><p>Clean the area and the gasket. I used some denatured alcohol on the paint, and just a dry rag on the gasket. Make sure all surfaces are bone dry before proceeding. If yours is wet, you can use a hair dryer to speed up the drying process.</p><p></p><p>[ATTACH=full]186295[/ATTACH]</p><p></p><p>Now apply your silicone. I used GE Silicone II in white for demo purposes, but you'd probably want to go with black or clear. If you can't find the GE stuff, make sure you pick a silicone that stays flexible, is waterproof and wont dry out with UV exposure. </p><p><img src="http://www.plumbersurplus.com/images/prod/5/GE-Silicone-GE281-rw-208187-317278.jpg" alt="" class="fr-fic fr-dii fr-draggable " style="" /></p><p></p><p>[ATTACH=full]186296[/ATTACH]</p><p></p><p>[ATTACH=full]186297[/ATTACH]</p><p></p><p>Carefully reattach the sockets to the housing (a quarter turn counter clockwise) and the LED connector by reclipping it in if you pulled the light all the way off, slide the light back in place and tighten down your screws. Don't tighten too much! You'll crack the plastic if you do. Also be careful not to cross thread your screws; a firm press before ******** in made sure mine were seated correctly.</p><p></p><p>I didn't use a dab of silicone on the screws, but you could if you wanted to be extra sure. </p><p></p><p>In theory, when a bulb blows this should pull off with the gentle help of a putty knife. I should then be able to clean up the old silicone, replace the bulb(s), reapply new and all should be well.</p><p></p><p>All told this took 10 minutes start to finish, including a few minutes of cleaning up the silicone that squeezed out the sides (I used a q-tip and ran it along the edges, wiping it off as I went). Time well spent given the serious headaches a leak up there can cause, and cost!</p></blockquote><p></p>
[QUOTE="BigJ, post: 136265, member: 62"] Been reading a lot lately about several folks discovering that their 3rd brake light is leaking. I've read that the results from that leak can range from no problems, to headliner staining, to hill decent control faults, ABS faults, to who knows what else. Bottom line? Ya really REALLY don't want that thing leaking. Here's the SSM that deals with it I've never had a problem, but mine was built before the SSM's cutoff date, so I figured I'd better be safe that sorry since I'm out of warranty. At a minimum Ford wants somewhere around $400 to replace the light (before labor!) and who knows what else to diagnose any other problems the leak caused. So I pulled it down and lined the edge with a bead of window and door silicone. I didn't find a how-to really, so I figured I'd make one just 'cause. Here's what mine looks like before the fix. A little weird, but no water leakage that I can tell: [ATTACH=full]186291[/ATTACH] [ATTACH=full]186292[/ATTACH] To pull it down, grab a #2 phillips screwdriver and slowly back out the two screws holding it in place [ATTACH=full]186293[/ATTACH] [ATTACH=full]186294[/ATTACH] A quarter turn clockwise on each socket will free it from the housing, and a quick press to release the clip drops the LED connector. I didn't bother since its simple enough to apply the silicone with it up there, but if your housing is wet or dirty, ya might want to so its easier to dry out and clean up. Clean the area and the gasket. I used some denatured alcohol on the paint, and just a dry rag on the gasket. Make sure all surfaces are bone dry before proceeding. If yours is wet, you can use a hair dryer to speed up the drying process. [ATTACH=full]186295[/ATTACH] Now apply your silicone. I used GE Silicone II in white for demo purposes, but you'd probably want to go with black or clear. If you can't find the GE stuff, make sure you pick a silicone that stays flexible, is waterproof and wont dry out with UV exposure. [img]http://www.plumbersurplus.com/images/prod/5/GE-Silicone-GE281-rw-208187-317278.jpg[/img] [ATTACH=full]186296[/ATTACH] [ATTACH=full]186297[/ATTACH] Carefully reattach the sockets to the housing (a quarter turn counter clockwise) and the LED connector by reclipping it in if you pulled the light all the way off, slide the light back in place and tighten down your screws. Don't tighten too much! You'll crack the plastic if you do. Also be careful not to cross thread your screws; a firm press before ******** in made sure mine were seated correctly. I didn't use a dab of silicone on the screws, but you could if you wanted to be extra sure. In theory, when a bulb blows this should pull off with the gentle help of a putty knife. I should then be able to clean up the old silicone, replace the bulb(s), reapply new and all should be well. All told this took 10 minutes start to finish, including a few minutes of cleaning up the silicone that squeezed out the sides (I used a q-tip and ran it along the edges, wiping it off as I went). Time well spent given the serious headaches a leak up there can cause, and cost! [/QUOTE]
Insert quotes…
Verification
Post reply
Members online
Tigmandick
wjoutlaw
Reptar854
Peej
So-Cal-Al-52
CleverGirl_
Digipax
jonnyV
DigbyRaptor
mikewills
Ruger86
MFouts
defjammm
ToadSmasher2K1
dillard09
Bowlmsc
refine
Sever18
AGENTX
hdvvraptor
Raptor Harris
Andy1320
WC114
jnall
downforce137
IIAWAH808
Krudenite
NACHOMASTER
tone
BigBlackRaptor24
Killdozer13
cyle
IHAVETWO
AZRaptorJohn
james9
riv
Zeusmotorworks
sixshooter_45
DFS
ss55539
Haydel53
socal raptor
jlaronde
elpechedepeche
Badamsmb
MDJAK
KAJRIP
Sage
icecoldak
Nyamg
... and 3 more.
Forum statistics
Threads
93,631
Posts
1,965,728
Members
56,935
Latest member
ID_AZ
Forums
Ford Raptor Forums - General Information
Ford Raptor Recalls | TSB's | SSM's
TSB 11-4-7 - Third Brake / Cargo Light / High Mounted Stop Lamp TSB/SSM and Fix
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
Accept
Learn more…
Top