Forums
New posts
Search forums
What's new
New posts
New profile posts
Latest activity
Members
Registered members
Current visitors
New profile posts
Search profile posts
Log in
Register
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
RAM TRX - TRX-Forum.com
Bronco Raptor - BroncoRaptorForum.com
Forums
Ford Raptor Forum Supporting Vendors
Freedom Motorsports
NEW Ford Raptor "Dead Pedal" Fabrication!
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="mudblood" data-source="post: 733120" data-attributes="member: 12963"><p>Your right...it will be a tricky proposition. With the vette pedals you had to drill holes right into the stock pedal and that was a real hard task with the vette pedals as they are rounded. Then you had to slide under the seat (no room at all) and try to screw in the new pedals while laying backwards. The issue is if you use bare metal to make it look good you give up any real traction. You use a rubber pad and your right where you started. It will take some thinking out of the box for these. I know there is some really rough line-x that may offer a good texture. I am sure if it can be done you guys will do it. Folks may not appreciate the difficulty in mass producing this kind of product and the huge risk taken in relation to the save driving factor of the consumer. The very best of luck on your endevor.</p></blockquote><p></p>
[QUOTE="mudblood, post: 733120, member: 12963"] Your right...it will be a tricky proposition. With the vette pedals you had to drill holes right into the stock pedal and that was a real hard task with the vette pedals as they are rounded. Then you had to slide under the seat (no room at all) and try to screw in the new pedals while laying backwards. The issue is if you use bare metal to make it look good you give up any real traction. You use a rubber pad and your right where you started. It will take some thinking out of the box for these. I know there is some really rough line-x that may offer a good texture. I am sure if it can be done you guys will do it. Folks may not appreciate the difficulty in mass producing this kind of product and the huge risk taken in relation to the save driving factor of the consumer. The very best of luck on your endevor. [/QUOTE]
Insert quotes…
Verification
Post reply
Members online
Socks
BlueHound
20Ecoboost17
fordrat
sukid
2slo4u
riv
justinh
FreightTerrain
RRR19-Mike
RogueClimber
Coyote_695
pat247
kshipp
hamster
Badboy4fun_wa
JustACowboy64
kevo_lo
dwc032
Keith88
Shane361
daytona1783
RCorsa
Kayslay
dillard09
Specialtyperformanceparts
RaptorFan1988
lawyerup
figure1a
Reptar854
ToadSmasher2K1
mleaky
Reaper308
Kisersosa
Chewie
Rmont3
mprice1234
dsg2003mach1
GOTSVT?
Viewsflores
maritn1000
DFS
JDzRptr
sheepdawg
Dan H
HOLLYWOOD 1
RaptorFun
pastorwug
JohnyPython
briangsxr1000
... and 13 more.
Forum statistics
Threads
93,629
Posts
1,965,673
Members
56,935
Latest member
ID_AZ
Forums
Ford Raptor Forum Supporting Vendors
Freedom Motorsports
NEW Ford Raptor "Dead Pedal" Fabrication!
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
Accept
Learn more…
Top